Our equipment is used in various areas of the foundry: from feeding the furnace, to cooling and transporting the castings, passing through green sand or sand-resin shakeout. We also offer applications for the processing lines, that collects and cools the sand before delivering it back to the sand plant.
Thanks to the continuous research and development in the foundry field, Vibroprocess has achieved very important goals during the last years, improving existing technologies such as the continuous discharging shakeout using “Vario Simplex “, an electronic system that controls the speed and the angle of line of force. The new software created for controlling the casting coolers also improved the overall control of the entire production line.
In the foundry field, as well as in the other application fields, our machines are designed for extreme work conditions and are manufactured based on our “ Heavy-Duty “ design principle.
Our vibrating screens for this field:
Vibrating screens
Vibrating screens for used sand
Vibrating screens for sand and sand blasting grit
Our furnace feeders for this field
Vibrating furnace feeders
Feeders with single carriage
Feeders with double carriage
Fifth wheel feeders
Support structures and rails
Carriages
Weighing systems
Remote control systems (radiocontrol)
Our discharge shakeouts for this field
Continuous shakeouts with conventional frequency (1000 rpm)
Continuous shakeouts with high frequency (1500 rpm)
Continuous VARIO shakeouts with variable frequency
Continuous VARIO SIMPLEX shakeouts with variable frequency
Vibrodrums
Table shakeouts (no-bake plants)
Our vibrating coolers for this field
Casting coolers
Sand coolers
Our vibrating conveyors for this field
Resonance conveyors
Casting and sand conveyors
Sorting conveyors
Conveyors for the removal of risers
Vibrating conveyors
Sand conveyors
Vibrating dosing feeders
Bidirectional / reversible
Heavy Duty
In the foundry field, as well as in the other application fields, our machines are designed for extreme work conditions and are manufactured based on our “ Heavy-Duty “ design principle.
Our experience is for
Cast iron – Steel – Brass – Copper – Aluminum – Steel alloys – Green sand
Mobile charging vibrating feeder 10 ton capacity
Our mobile charging vibrating feeders can be loaded in different ways like spider crane, magnet crane, skip or with customized special solution to accommodate customer requirements. Vibroprocess has manufactured the biggest equipment with 2.2 mt width and 7.5mt length; the mobile charging vibrating feeders are completely assembled with bolts and fully match the well know Vibroprocess “heavy duty design”.
Mobile charging vibrating feeders for electric furnace
The mobile charging vibrating feeders are the ideal solution to feed scraps and additives into electric furnaces for the smelting of ferrous and non ferrous. Vibroprocess range covers from 300 kg up to 40.000 kg batch capacity and are capable to travel on rails both longitudinal and transverse direction according to loading area and furnaces location on the platform. On request the system can be supplied with load cells weighing system.
Mobile charging vibrating feeder 12 ton capacity
Mobile charging vibrating feeder with the dimension of 1700×4500 mm. The vibrating machine and his bin are coated with interchangeable bolted wear material composed of a combination between high resistant steel and vulcanized rubber. This special wear system protect the structures from the impacts caused by the load of the products. The shown mobile charging vibrating feeder is complete of single trolley in order to allow the longitudinal translation.
Mobile charging vibrating feeder 15 ton capacity
Mobile charging vibrating feeder with the dimension of 1700×5000 mm, capable to charge two electric furnaces thanks to the double trolley that allow the longitudinal and transversal translations of the vibrating machine. This mobile charging vibrating feeder is designed to handle 15 ton/batch of ferrous scraps and it is installed in one of the most important Georgian foundry.
Mobile charging vibrating feeders 8 ton capacity
Our range of mobile charging vibrating feeders incorporate all the necessary safety devices such us audio-visible signals, safety switch cables and emergency push button. All the Vibroprocess mobile charging vibrating feeders can be remotely controlled using a remote control device ensuring a safe working environment for the operators.
Mobile charging vibrating feeder 3 ton capacity
The shown mobile vibrating feeder is suitable for charge two side by side smelting furnaces thanks to the slewing truck operation it can rotate and move in longitudinal way. The Vibroprocess mobile charging vibrating feeders are driven by two unbalanced motors in order to allow an extreme accuracy dosing process.
Shake out table
The Vibroprocess shake out tables are designed for sand and casting separation of big size moulds. The heavy duty design allows to handle moulds with overdeck load up to 60 ÷ 70 tons and therefore suitable for big steel and cast iron castings. The drive system consist of our special mechanical exciters with oil lubrication which grant a long life operation expectancy.
Multiple Shake out tables
In the event of very large moulds dimension the Vibroprocess shake out tables can be installed side by side in order to reach an enormous shake out area. The shown multiple shake out table reach the total dimension of 4000 x 6000 mm and is driven by 4 rotational force exciters. The exhausted sand will be collect below the machines.
Continuous shake out – normal frequency (1000 rpm)
The normal frequency continuous discharging shake out operate at 1000 rpm. This application has the added advantage of being cheaper than the high frequency and Vario versions. The Vibroprocess continuous shake out desing is customized time to time in order to match the customers requirements. The selection of the shake outs grid by our engineers is always very accurate and a focal point in order to obtain the maximum performance in terms of sand and castings separation, avoiding the castings damage.
Foundry shakeout line
The normal frequency continuous discharging shake out operate at 1000 rpm. This application has the added advantage of being cheaper than the high frequency and Vario versions. The Vibroprocess continuous shake out desing is customized time to time in order to match the customers requirements. The selection of the shake outs grid by our engineers is always very accurate and a focal point in order to obtain the maximum performance in terms of sand and castings separation, avoiding the castings damage.
Continuous shake out – high frequency (1500 rpm)
The high frequency continuous discharging shake out operate at 1500 rpm. With this application the performance in terms of sand casing separation increase. We obtain also a lower rejection rate for the delicate castings, due to our high frequency – low amplitude system. Minimum damage to castings and high efficiency separation is ensured by optimum compatibility of the type of grid and the vibration data with the casting program. He shown continuous shake out have the dimensions of 1250×6000 mm.
Continuous shake out – Vario (1000 ÷ 1500 rpm)
The Vario continuous discharging shake out operate between 1000 and 1500 rpm. The Vario Simplex has been developed by Vibroprocess and gives a very high efficiency for the castings and sand separation with an impressive advantage in terms of cost if compared to previous PLC controlled Vario range. The Vario continuous shake outs are driven by four rotational motion exciters located on the sides.
Continuous shake out – Vario (1000 ÷ 1500 rpm)
The Vario continuous shake out has been developed in order to minimize the capital investment of foundries while obtaining, at the same time, all the advantages of the Vario shakeout. Thanks to “Vario Simplex”, the frequency and the angle of line of force is automatically adjusted by “Simplex Drive” according to casting program and customer requirements. The Vario continuous shake out grants the best sand lamps disintegration and minimal damages to castings.
Vibrating drum
Vibroprocess vibrating drum are used to continuously unwrap and cool the most different type of casting. whether it’s hot plates or valve castings that’s involved. The unwrapping process is very gentle while cooling is pronouncedly effective (down from 700 °C to 60 °C). Good homogenization of the sand in the vibrating drum while in the process of being cooled down considerably facilitates subsequent sand preparation. Vibroprocess vibrating drums operate on the micro-throw principle. The unidirectional force exciters, generate linear vibrations applied here to unwrapping and handling.
Casting cooler line
The modern foundries the necessity to accelerate the production process time and therefore to make shorter the required cooling time. The casting cooler line represents the answer to such necessity. These equipment can handle castings with inlet temperature of 650 ÷ 700 °C and are able to decrease the temperature below 100 °C. The casting cooler lines can handle castings and sand in order to transport and temperature decreasing of them.
Casting cooler line
The Vibroprocess casting coolers exploit the resonance vibration in order to handle castings and sand. Thanks to this kind of vibration is possible to transport the products in a very gently way, avoiding any type of castings damages. The base frame of our casting coolers ensure a complete insulation from vibrations of the machine. The shown casting coolers compose a 28 meter long line, installed in one of the bigger foundries in India.
Casting cooler line
The shown casting cooler line is installed in a prestigious Italian foundry. This casting cooler is installed with an upward inclination of 5° in order to fully match with client layout requirement. This casting cooler is 20 meters long and is designed for decrease the casting temperature from 600 °C to 80 °C thanks to the ventilation system compose by a fan that blow air upstream inside the channel.
Resonance conveyors
The picture shown a complete line of Vibroprocess sand and castings resonance conveyors, installed in one of the most important Indian foundries.
These machines compose a complete line that reach a total lenght of 60 meters. Our resonance conveyors are driven by frequency converters in order to control the vibration frequency and the speed of the castings and sand.
Resonance conveyors
The Vibroprocess resonance conveyors are the ideal solution in order to conveying hot or abrasive products in foundry.The resonance conveyors can replace the typical apron conveyors; one single machine can reach 30 meter length without any problems like the sand falling. These machines can be designed in order to perfect match with costumers layout necessity, our turn sections of the vibrating conveyors are very required and appreciated by our clients. The Vibroprocess resonance conveyors stand out also for the very silent operation and easy assembling.
Resonance conveyors
In the picture, a complete line of Vibroprocess sand and castings resonance conveyors, installed in one of the most important Indian foundries.
The shown machines compose a complete line that reach a total lenght of 60 meters. Our resonance conveyors are driven by frequency converters in order to control the vibration frequency and the speed of the castings and sand of this kind.
Resonance conveyors
The shown Vibroprocess resonance conveyors are use for casting and sand conveyor. The resonance conveyors can be installed in line in order to reach longer distances. The resonance conveyors are provided complete of isolation frame in order to avoid the environmental vibrating transmission. The combination between different type of coil springs guarantee che complete isolation efficiency. The isolation performance reach 95%.
Resonance sorting conveyor
The Vibroprocess resonance sorting conveyors are characterized by an high robustness and an excellent vibrations isolation degree. These machines can reach dimensions of 15 meters long and 2.60 meters wide with flow rate up to 30,000 kg/h.
In the shown picture, the castings are manually selected by operators after the shot blast machine, which divide them by type. Following the castings are conveyed in special bins or directly on belts conveyors.
Mechanical vibrating feeders
The Vibroprocess vibrating conveyors are customized on customer different installation requirements. The shown vibrating conveyor discharge mouth perfectly match with the next application, in this case, a rotating drum. These machines are driven by unidirectional force mechanical exciters or by unbalanced motors. The mechanical vibrating feeders are designed in order to convey sand and castings.
Vibrating sand cooler
The Vibroprocess vibrating sand coolers are designed in order to homogenize and cool down the return sand temperature in a continuous cycle (from 120 °C up to 40 °C).
This allow to obtain a reduction of the mixing time and an higher sand quality. The model shown in the photograph is driven by unidirectional mechanical oscillators and connected to the electric motor through cardan shaft.
Vibrating sand cooler
The shown vibrating sand cooler has the capacity of 150 t / h of sand and is installed in one of the most important foundries of Great Britain. The sand cooler operates with the principle of the fluidized bed in order to cool down the temperature of the sand.
The Vibroprocess vibrating sand coolers are provided complete of the additional water system in order to increase the moisture percentage of the sand.
